2014: Recent submissions

  • DOGOTARU, S.; URSU, M. (Technical University of Moldova, 2014)
    This paper analyzes the existing Housing Stock ]n the view of administration of buildings belonging to several owners. Following the privatization of the housing stock and due to shortcomings in legislation, apartment ...
  • PUIU, C.; IAGĂRU, R.; PUIU, V.; NEAMŢU, Fl. V. (Technical University of Moldova, 2014)
    This work intends to sustain the fact that a process of measuring the consumer’s satisfaction carried out in an objective and correct manner, may offer the necessary data and information for making compatible, within the ...
  • LIVINŢ, G.; LUCACHE, D. D.; DĂNILĂ, E. (Technical University of Moldova, 2014)
    The paper deals with the synthesizing of a polynomial RST controller to insure the stability of a flywheel energystorage system. Considering variations of the constructive parameters and perturbation, by means of simulation ...
  • GUŢU, M. (Technical University of Moldova, 2014)
    This paper presents the final design of glass-reinforced polyester (GRP) blade for small wind turbine developed at the Technical University of Moldova by finite element (FE) analysis techniques. The design variables ...
  • BOSTAN, I.; DULGHERU, V. (Technical University of Moldova, 2014)
    Some problems of mechanical transmissions can be solved with special effects by developing new types of transmissions based on planetary precessional transmissions with multiple gear, that were developed by the author. ...
  • BÂRSAN, A. (Technical University of Moldova, 2014)
    The paper proposes some kinematical optimizing solutions for the Geneva mechanism. Three mechanisms are presented: a curved slotted Geneva mechanism, a “Y” type Geneva mechanism and a conventional Geneva mechanism driven ...
  • RUSANOVSCHI, M.; STOICEV, P.; RUSANOVSCHI, V. (Technical University of Moldova, 2014)
    In this paper are given the results of the study of crystal structures in terms of determining the conformational differences, the quantitative comparison of the geometry of complex cations, transition metals of rhodium ...
  • CHIRICUŢĂ, I. (Technical University of Moldova, 2014)
    This article deals with possible use of slag steelworks in road construction. The storage of slag steelworks in waste dumps pose serious environmental problems by occupation of large areas of land and instability of dump ...
  • MANOLI, I.; BEIU, I. (Technical University of Moldova, 2014)
    In the article technical and economical aspects of the vehicle adjustment to CNG supply are presented. Aspects of the diesel oil and petrol engines adaptation to CNG were also brought up. Another significant factor which ...
  • DEREVJANKO, V. N.; NECHITAYLO, N. P. (Technical University of Moldova, 2014)
    This work analyzes factors, that lead to fouling of membrane elements during operation. Special attention is given to biofouling of membrane elements, which is the basic factor, that leads to critical decrease of membrane ...
  • SVEATENCO, N. (Technical University of Moldova, 2014)
    The volume element V0 , being isotropic and homogeneous at the macroscopic level, can be represented as a conglomerate composed of an infinite number of kinematically connected subelements. Structural element identifies ...
  • PÎNTEA, V.; MACIUGA, A.; RADU, R.; STOICEV, P.; KULEV, M. (Technical University of Moldova, 2014)
    The paper presents the results of investigations on the influence of excitation conditions (temperature, intensity, exciting impulse duration) and proposes the mechanism of super luminescence phenomenon, a phenomenon that ...
  • CUCU, O.; TODOS, P.; GHENCEA, C.; GUVIR, S. (Technical University of Moldova, 2014)
    An important role in university training of the future specialists lies on the internships, which is a first step towards adapting and integrating students into the professional environment. The efficiency of internships ...
  • IVASHENKO, N.; BULYANDRA, A.; VERBITSKIY, B.; LUTZIK, Yu.; BERNIC, M.; CIOBANU, E. (Technical University of Moldova, 2014)
    The article presents some beet pulp micropore volume, integral and differential distribution curves of micropores by radiuses, effective pore radius, and surface area. It is shown their influence on the drying process.
  • RACHIER, V.; SOBOR, I.; CHICIUC, A. (Technical University of Moldova, 2014)
    According to Moldova’s National Renewable Energy Action Plan, renewable electricity will be produced mainly from wind and by 2020 is necessary about 400 MW wind capacity. In this paper an attempt is made to assess the wind ...
  • MARINA, V.; MARINA, Viorica (Technical University of Moldova, 2014)
    The scientific and technologic progress is conditioned by level of knowing of material behaviour in function of his structure and history of exterior action. Studding of relations between stress and strain tensors can’t ...
  • BĂJENESCU, Titu-Marius I. (Technical University of Moldova, 2014)
    There are many problems and challenges which must be overcome during the implementation phase of all projects. Some are overcome with engineering redesign and hard work, while others require more investment by the manufacturer. ...
  • MANOLEA, Gheorghe (Tehnica UTM, 2014)
  • DULGHERU, Valeriu (Tehnica UTM, 2014)
  • GUTIUM, O.; CIUMAC, J. (Tehnica UTM, 2014)
    Activitatea ureazică a boabelor de năut este influenţată de hidratarea şi germinarea boabelor, temperatura şi compozitia mediului de fierbere şi de durata fierberii. Temperatura optimă pentru ureaza năutului este 600C. ...

Search DSpace


Advanced Search

Browse

My Account