DSpace Repository

Design and Manufacturing Method of GFRP Blades for Vertical Axis Wind Turbine

Show simple item record

dc.contributor.author BERE, Paul
dc.contributor.author CIOBANU, Radu
dc.contributor.author CIOBANU, Oleg
dc.contributor.author GUȚU, Marin
dc.date.accessioned 2021-12-13T09:17:41Z
dc.date.available 2021-12-13T09:17:41Z
dc.date.issued 2021
dc.identifier.citation BERE, Paul, CIOBANU, Radu, CIOBANU, Oleg. Design and Manufacturing Method of GFRP Blades for Vertical Axis Wind Turbine. In: IOP Conference Series: Materials Science and Engineering. 2021, V. 1190, N. 1, pp. 012022. ISSN 1757-899X, 1757-8981. en_US
dc.identifier.issn 1757-899X
dc.identifier.issn 1757-8981
dc.identifier.uri https://doi.org/10.1088/1757-899x/1190/1/012022
dc.identifier.uri http://repository.utm.md/handle/5014/18405
dc.description Access full text - https://doi.org/10.1088/1757-899x/1190/1/012022 en_US
dc.description.abstract Today, environmental protection and the rational use of natural resources have become growing challenges. One of these aspects is energy producing with less impact on the environment. For some applications the small wind turbines can be a solution. In this paper are presented some aspects regarding the design and manufacturing technology of 500 W vertical axis wind turbine blades. The turbine will be installed in the urban environment so that requirements regarding rotor aesthetics and noise level will be considered. The optimal geometric parameters of the turbine rotor were determined by specialized MathCAD and elaborated in 3D modelling software. For the blades the NACA 0018 airfoil was used with the chord length of 110 mm and is constant throughout the length of the blade. The blades are helical and are 1800 mm long. To estimate the aerodynamic performance of the turbine rotor, a computational fluid dynamics model was developed using ANSYS CFX finite element analysis software. The authors proposed a new method for rapid prototyping of blades using fused deposition modelling procedure. In order to increase the mechanical properties, the blades were covered with several layers of glass-fibres reinforced polymer. Estimation the blade strength to operating loads was performed using Ansys Workbench software. The modelling of the composite material architecture on the blade surface was performed using the special ANSYS Composite PrepPost module. Several simulations were performed with different number of layers and stacking sequences. In order to prevent rotor over engineering the maximum rotation speed of 400 min−1 was accepted (equivalent to ≍12 m/s wind speed). Simulation of the blade strength to operating loads indicate values of around 40 MPa for shear stress (50% less than failure shear stress) and around 80 MPa principal stress (60% less than failure tensile stress). The maximum blade deformations of 3 – 4 mm shows that the blade is stiff enough at imposed operation conditions. For the blade manufacturing, based on the numerical analysis results, the configuration of the strength structure composed of 5 layers of GFRP was selected, which forms a total blade weight of 1895g. en_US
dc.language.iso en en_US
dc.publisher IOP Publishing en_US
dc.rights Attribution-NonCommercial-NoDerivs 3.0 United States *
dc.rights.uri http://creativecommons.org/licenses/by-nc-nd/3.0/us/ *
dc.subject wind turbines en_US
dc.subject blades en_US
dc.subject wind turbines blades en_US
dc.title Design and Manufacturing Method of GFRP Blades for Vertical Axis Wind Turbine en_US
dc.type Article en_US


Files in this item

The following license files are associated with this item:

This item appears in the following Collection(s)

Show simple item record

Attribution-NonCommercial-NoDerivs 3.0 United States Except where otherwise noted, this item's license is described as Attribution-NonCommercial-NoDerivs 3.0 United States

Search DSpace


Advanced Search

Browse

My Account